Latest topics
» New Member
Today at 2:04 am by stevenbell

» Frame end plugs
Thu Mar 21, 2019 9:07 pm by kerabo

» Falcon Trials & Scrambler Fuel Tanks
Thu Mar 21, 2019 7:58 pm by peter@dunfordconstruction

» New Rims for plover
Thu Mar 21, 2019 7:45 pm by Rex Stewart

» 2019 Event List update
Thu Mar 21, 2019 7:38 pm by John Wakefield

» Cambridge Classic Bike Show
Thu Mar 21, 2019 4:55 pm by John Wakefield

» Old pre-mix.
Mon Mar 18, 2019 4:11 pm by kerabo

» Browser problems
Mon Mar 18, 2019 12:10 pm by zorteus

» shows old and new
Mon Mar 18, 2019 12:01 pm by zorteus


New kickstart

Go down

New kickstart

Post  kerabo on Sat Jan 12, 2019 5:21 pm

I have a nice new large spline kickstart for sale. I was going to convert it but changed my mind. This was imported and I though I bad a deal but they hit me with import duties so it cost me almost twice the starting price.  

https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.co.uk%2Fulk%2Fitm%2F283336665713

Ken
kerabo
kerabo

Posts : 2645
Join date : 2008-02-11
Age : 68
Location : Falcon 87..1936 Cruiser 39. Falcon 81 Green Lane bitsa. Sunbeam S8. Honda Deuville.

Back to top Go down

Kick start

Post  piston 197 on Sat Jan 12, 2019 5:30 pm

Ken the spline will fit the twins, but the kickstart will not, the twin ones are straight without the crank at the bottom, this one will foul the casing and cause breakage ,
This is for the 4 speed gearbox fitted to later 9E/4 ( early ones are 5/8" spline) and A series 250cc engine 31A.32A.33A.34A,35A,36A,37A

JH
piston 197
piston 197
Moderator

Posts : 4309
Join date : 2008-08-17
Location : ross-on-wye

Back to top Go down

Kickstart

Post  kerabo on Sat Jan 12, 2019 5:35 pm

Thanks John.

You mean it will hit where the gear indicator is on the casing?

Regards Ken
kerabo
kerabo

Posts : 2645
Join date : 2008-02-11
Age : 68
Location : Falcon 87..1936 Cruiser 39. Falcon 81 Green Lane bitsa. Sunbeam S8. Honda Deuville.

Back to top Go down

Kickstart

Post  piston 197 on Sat Jan 12, 2019 5:41 pm

It will not fit the twin with the casing intact, it will either break the casting where the gear indicator plate is situated when kicked over, or the casing will have to have a piece cut out of it before it will work, The spine is the correct size, but the twin has a Kickstart with a straighter shaft which just leans out at an angle without the swan neck which is required on the single cylinder one to miss the clutch adjuster.
JH
piston 197
piston 197
Moderator

Posts : 4309
Join date : 2008-08-17
Location : ross-on-wye

Back to top Go down

Re: New kickstart

Post  kerabo on Sat Jan 12, 2019 6:14 pm

piston 197 wrote:It will not fit the twin with the casing intact, it will either break the casting where the gear indicator plate is situated when kicked over, or the casing will have to have a piece cut out of it before it will work, The spine is the correct size, but the twin has a Kickstart with a straighter shaft which just leans out at an angle without the swan neck which is required on the single cylinder one  to miss the clutch adjuster.
JH

Thank you John
kerabo
kerabo

Posts : 2645
Join date : 2008-02-11
Age : 68
Location : Falcon 87..1936 Cruiser 39. Falcon 81 Green Lane bitsa. Sunbeam S8. Honda Deuville.

Back to top Go down

Re: New kickstart

Post  Sponsored content


Sponsored content


Back to top Go down

Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum