Latest topics
» New Member
Today at 2:04 am by stevenbell

» Frame end plugs
Thu Mar 21, 2019 9:07 pm by kerabo

» Falcon Trials & Scrambler Fuel Tanks
Thu Mar 21, 2019 7:58 pm by peter@dunfordconstruction

» New Rims for plover
Thu Mar 21, 2019 7:45 pm by Rex Stewart

» 2019 Event List update
Thu Mar 21, 2019 7:38 pm by John Wakefield

» Cambridge Classic Bike Show
Thu Mar 21, 2019 4:55 pm by John Wakefield

» Old pre-mix.
Mon Mar 18, 2019 4:11 pm by kerabo

» Browser problems
Mon Mar 18, 2019 12:10 pm by zorteus

» shows old and new
Mon Mar 18, 2019 12:01 pm by zorteus


10E engine screws

Go down

10E engine screws

Post  FBKev on Sun Jan 06, 2019 5:13 pm

Took the James for a quick spin today and James my son rode an old British bike for the 1st time (he is 31) and hasn't stopped grinning yet totally blown away by easy nature and people of all ages looking and pointing. The steering has no play at the headstock but is very very light side to side. The falcon is what I would call normal light but with a little resistance. Having a look it appears that they are tweaked from below The stem has flats and there are two nuts locked together is it just a case of very gently adjusting from below? Also what is the thread and length of the two CSK screws that attach the engine side cover to the inner magneto cover with a stud at the front original part no E9260.
Thanks in advance.
Kev.
FBKev
FBKev

Posts : 128
Join date : 2018-06-17
Age : 58
Location : SE Kent

Back to top Go down

screws

Post  piston 197 on Sun Jan 06, 2019 5:27 pm

Timing case screws i am sure are 1/4 BSF
Yes to adjust the headstock bearings undo the lock nut by holding the flat on the shaft with a spanner, tighten up the upper nut to the desired setting and tighten the lock nut
CAUTION do not over tighten as you can end up with a proper tank slapper if too tight !

JH
piston 197
piston 197
Moderator

Posts : 4309
Join date : 2008-08-17
Location : ross-on-wye

Back to top Go down

Re: 10E engine screws

Post  FBKev on Sun Jan 06, 2019 6:33 pm

Thanks JH that is what I thought you are right though they only need a gnats. I will look for some BSF screws for the case, are they just a normal CSK or is it a specialised angle?
Kev.
FBKev
FBKev

Posts : 128
Join date : 2018-06-17
Age : 58
Location : SE Kent

Back to top Go down

Timing case screws

Post  piston 197 on Sun Jan 06, 2019 6:38 pm

Villiers services do them with correct length, csk,and thread
JH
piston 197
piston 197
Moderator

Posts : 4309
Join date : 2008-08-17
Location : ross-on-wye

Back to top Go down

Re: 10E engine screws

Post  FBKev on Sun Jan 06, 2019 6:45 pm

piston 197 wrote:Villiers services do them with correct length, csk,and thread
JH
Thanks.
FBKev
FBKev

Posts : 128
Join date : 2018-06-17
Age : 58
Location : SE Kent

Back to top Go down

Re: 10E engine screws

Post  FBKev on Tue Jan 08, 2019 5:28 pm

Looking for some socket heads CSK engine case screws for the Villiers 9/10E Original screws are 1/4" BSF X 2 3/8" does anyone know of a supplier where I can get some? I can get originals from Villiers services but would like to get some allen headed ones.
Kev.
FBKev
FBKev

Posts : 128
Join date : 2018-06-17
Age : 58
Location : SE Kent

Back to top Go down

Re: 10E engine screws

Post  peter@dunfordconstruction on Wed Jan 09, 2019 9:54 am

Try Custom Fastners Ltd They used to do them
peter@dunfordconstruction
peter@dunfordconstruction

Posts : 355
Join date : 2014-10-28
Location : Lymington Hampshire

http://peter@dunfordconstruction.co.uk

Back to top Go down

Re: 10E engine screws

Post  FBKev on Wed Jan 09, 2019 10:02 am

Bit the bullet and ordered some from Villiers services but thanks for your help.
Kev.
FBKev
FBKev

Posts : 128
Join date : 2018-06-17
Age : 58
Location : SE Kent

Back to top Go down

Re: 10E engine screws

Post  Sponsored content


Sponsored content


Back to top Go down

Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum