Latest topics
» Speedo drive - Rear wheel
Yesterday at 7:31 pm by peter@dunfordconstruction

» Battery Help
Yesterday at 2:07 pm by FBKev

» Yorkshire police Falcon
Tue Jan 22, 2019 1:02 pm by piston 197

» Cruiser oil
Mon Jan 21, 2019 6:48 pm by kerabo

» One from every year
Mon Jan 21, 2019 8:12 am by piston 197

» American thoughts of a British Bike Cruiser 39.
Sun Jan 20, 2019 5:10 pm by John Wakefield

» NEW CLUB MEMBERS
Sun Jan 20, 2019 10:40 am by piston 197

» Cruiser 39 gear change
Sat Jan 19, 2019 5:16 pm by kerabo

» Re-register Cruiser/Falcon
Sat Jan 19, 2019 1:08 pm by peter@dunfordconstruction


Miller switch

Go down

Miller switch

Post  kerabo on Sat Oct 27, 2018 10:25 am

Does anyone know how this Miller switch removes from its dash?
I can't see anything from underneath holding it.

Thanks Ken





kerabo
kerabo

Posts : 2580
Join date : 2008-02-11
Age : 68
Location : Falcon 87..1936 Cruiser 39. Falcon 81 Green Lane bitsa. Sunbeam S8. Honda Deuville.

Back to top Go down

Re: Miller switch

Post  John Wakefield on Sat Oct 27, 2018 6:18 pm

There are usually two studs molded into the outer bezel. Have you tried undoing the nut (and presumably one opposite) shown in the top pic?

John Wakefield

Posts : 105
Join date : 2017-08-31

Back to top Go down

Switch

Post  kerabo on Sat Oct 27, 2018 6:21 pm

As yet John there is no nut. There may be something under the cover but it is starting to crack if I prize it.

Thanks Ken
kerabo
kerabo

Posts : 2580
Join date : 2008-02-11
Age : 68
Location : Falcon 87..1936 Cruiser 39. Falcon 81 Green Lane bitsa. Sunbeam S8. Honda Deuville.

Back to top Go down

Re: Miller switch

Post  John Wakefield on Sat Oct 27, 2018 6:25 pm

There is a nut on the contact to the left of the tall one with resistance attached, is there not another one opposite. These nuts are on the two studs that clamp the outer bezel to switch through the dash

John Wakefield

Posts : 105
Join date : 2017-08-31

Back to top Go down

Re: Miller switch

Post  davin999 on Sat Oct 27, 2018 7:10 pm

John Wakefield wrote:There is a nut on the contact to the left of the tall one with resistance attached, is there not another one opposite. These nuts are on the two studs that clamp the outer bezel to switch through the dash


Ken this is what John means,this Miller switch is fitted to my post war Vincent you just undo the two nuts and it should come apart, pre war switches may differ i`ll have a look at my Cruiser in the morning and see if it`s the same.

davin999

Posts : 50
Join date : 2018-06-09

Back to top Go down

Switch

Post  kerabo on Sat Oct 27, 2018 8:41 pm

Well done I was starting to get worried.

Thanks a lot

Ken
kerabo
kerabo

Posts : 2580
Join date : 2008-02-11
Age : 68
Location : Falcon 87..1936 Cruiser 39. Falcon 81 Green Lane bitsa. Sunbeam S8. Honda Deuville.

Back to top Go down

Re: Miller switch

Post  Sponsored content


Sponsored content


Back to top Go down

Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum