Latest topics
» Battery Help
Today at 2:07 pm by FBKev

» Yorkshire police Falcon
Yesterday at 1:02 pm by piston 197

» Cruiser oil
Mon Jan 21, 2019 6:48 pm by kerabo

» One from every year
Mon Jan 21, 2019 8:12 am by piston 197

» Speedo drive - Rear wheel
Sun Jan 20, 2019 5:32 pm by piston 197

» American thoughts of a British Bike Cruiser 39.
Sun Jan 20, 2019 5:10 pm by John Wakefield

» NEW CLUB MEMBERS
Sun Jan 20, 2019 10:40 am by piston 197

» Cruiser 39 gear change
Sat Jan 19, 2019 5:16 pm by kerabo

» Re-register Cruiser/Falcon
Sat Jan 19, 2019 1:08 pm by peter@dunfordconstruction


Help wanted for 1958 Falcon 81

Go down

Help wanted for 1958 Falcon 81

Post  trophy on Sat Sep 08, 2018 6:52 pm

Bought recently as a box of bits. Engine sorted but need advice on a few other things:-
1) The carburettor body has no model number, only "Villiers", then "shaw" encased inside a diamond shape. Throat size is 24mm. Throttle slide is Number 3. Choke slide WDC 1. 120 main jet. Jet needle 3 & 1/2. No marking on the pilot jet. Float chamber stamped Mk 111. Air filter is a V.1800B. Is this set-up suitable for the bike?
2) I fitted new rear wheel bearings and stupidly didn't note which way the spindle came out. Only noticed that one end is slightly longer than the other. Can anyone confirm which side does the longer end go to? The manuals are no help.
3) Any recommendations on tyres? Has the front to be ribbed?
4) Both brakes need re-lining. Who would you send them to?
5) One of the footrests has been butchered, anyone got a pair I can purchase?
6) Also need a 48T rear wheel sprocket. Who would stock these, the club maybe?
All (any) replies appreciated.
Ride safe all.

trophy

Posts : 12
Join date : 2018-08-11
Location : Millom. Cumbria.

Back to top Go down

Falcon 81

Post  piston 197 on Sun Sep 09, 2018 7:26 am

1 carb should be a S25 Villiers early ones had no number stamped on them 120 main jet and 3 1/2 slide are correct for a 10E, the nedle should be set 1.95" out from the bottom of the flat surface of the carb ( may need adjusting for wear to get optimum position)
2 if you have it in the wrong way your sprockets will not align, put it in the wheel and put the wheel in the frame if it aligns it is ok , if not change it round, from memory i think the long side is to the opposite of the sprocket? but it has been a while
3 your choice
4 Villiers service will reline your brake shoes

JH
piston 197
piston 197
Moderator

Posts : 4222
Join date : 2008-08-17
Location : ross-on-wye

Back to top Go down

Falcon 81

Post  trophy on Sun Sep 09, 2018 7:35 pm

Many thanks JH.

trophy

Posts : 12
Join date : 2018-08-11
Location : Millom. Cumbria.

Back to top Go down

Re: Help wanted for 1958 Falcon 81

Post  peter@dunfordconstruction on Mon Sep 10, 2018 1:46 pm

Hi Trophy,

I do have a 48 tooth sprocket give me your E-mail and I will send details & photo

Peter
peter@dunfordconstruction
peter@dunfordconstruction

Posts : 347
Join date : 2014-10-28
Location : Lymington Hampshire

http://peter@dunfordconstruction.co.uk

Back to top Go down

sprocket

Post  trophy on Mon Sep 10, 2018 2:07 pm

Thanks Peter. Have PM'd you.

trophy

Posts : 12
Join date : 2018-08-11
Location : Millom. Cumbria.

Back to top Go down

Re: Help wanted for 1958 Falcon 81

Post  Sponsored content


Sponsored content


Back to top Go down

Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum