Latest topics
» 2t Villiers Electronic Ignition etc
Yesterday at 9:06 pm by stuart elkes

» Cruiser 39 Dynamo
Yesterday at 3:10 pm by kerabo

» Cruiser piston rings needed please
Tue Oct 16, 2018 10:40 am by kerabo

» WIRING HARNESS WANTED
Tue Oct 16, 2018 10:38 am by kerabo

» Stafford Show
Mon Oct 15, 2018 6:39 pm by stuart elkes

» What's this?
Sun Oct 14, 2018 8:34 pm by piston 197

» head bolts 8e
Sun Oct 14, 2018 12:55 pm by alan67

» Copdock and Scotland
Sat Oct 13, 2018 7:21 am by alan67

» 2 7/8" tank badges
Fri Oct 12, 2018 10:00 pm by FrankG


centre stand

Go down

centre stand

Post  Mcventures on Wed Jul 25, 2018 2:13 pm

i know ive asked this earlier but im going to try again. im looking for a centre stand for a francis barnett falcon 1959 , please let me know if you have one lying around which you are willing to sell, as mine is bent.
cheers scott.

Mcventures

Posts : 13
Join date : 2018-05-23

Back to top Go down

centre stand

Post  mike Sayer on Wed Jul 25, 2018 6:41 pm

Scott, what about straightening it, or is it too far gone? I would certainly give it a go before consigning it to the trash bin. Can I help in any way?
Mike.
avatar
mike Sayer

Posts : 253
Join date : 2008-02-12
Age : 78
Location : east of England

Back to top Go down

Re: centre stand

Post  Mcventures on Wed Jul 25, 2018 8:36 pm

Itís only minimally bent but itís enough to tip the bike over when on the stand . I have attempted to bend it back using brute force with hammer but no luck . Would you say using a blow torch and a hammer is likely to break it ? Cheers for replying mike
Scott

Mcventures

Posts : 13
Join date : 2018-05-23

Back to top Go down

Re: centre stand

Post  peter@dunfordconstruction on Thu Jul 26, 2018 8:00 am

Hi Scott,

I have a couple of spare F/B centre stands Not sure which model they are for if you send me a photo I will check to see if they are correct,

Peter

peter@dunfordconstruction

Posts : 309
Join date : 2014-10-28
Location : Lymington Hampshire

http://peter@dunfordconstruction.co.uk

Back to top Go down

Re: centre stand

Post  Mcventures on Thu Jul 26, 2018 10:35 am

Ahh briliant hopefully thia photo may Be some help
Cheers Peter
Scott


Mcventures

Posts : 13
Join date : 2018-05-23

Back to top Go down

bent centre stand

Post  mike Sayer on Sat Jul 28, 2018 11:31 am

Hi Scott, in my experience, using brute force is rarely successful. I would suggest the use of heat around the distorted area will make it much easier to return the stand to its proper shape, (providing you know what the proper shape is!) I would discard the hammer & work out a strategy for correcting the distortion before wading in indiscriminatingly. However, if a straight stand for your bike is available, then perhaps you should snaffle it up tout suite. Don`t dispose of the bent one as I am pretty sure it will be repairable & could get another FBOC member out of trouble.
Regards, Mike.
avatar
mike Sayer

Posts : 253
Join date : 2008-02-12
Age : 78
Location : east of England

Back to top Go down

Re: centre stand

Post  Rex Stewart on Sat Jul 28, 2018 12:24 pm

I saw a centre stand on ebay yesterday, I will see if I can find it again.

Rex Stewart

Posts : 36
Join date : 2017-09-21
Age : 68
Location : Aberdeenshire

Back to top Go down

Re: centre stand

Post  peter@dunfordconstruction on Sat Jul 28, 2018 4:32 pm

Hi Scott,

Found 2 of them different sizes 12" across Feet x 14" high If you let me have your Email address I will send Pics

Peter

peter@dunfordconstruction

Posts : 309
Join date : 2014-10-28
Location : Lymington Hampshire

http://peter@dunfordconstruction.co.uk

Back to top Go down

Re: centre stand

Post  Sponsored content


Sponsored content


Back to top Go down

Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum