Latest topics
» Cruiser 80 speedo
Yesterday at 11:00 pm by intrudin

» Plover 78 Front footrest
Yesterday at 8:01 pm by Gyrocopter

» wheel bearings knock through spindle
Yesterday at 3:52 pm by piston 197

» Wicker Basket
Sat Dec 08, 2018 8:39 pm by keith.hodgenia

» Wicker Basket
Sat Dec 08, 2018 8:33 pm by kerabo

» Spalding Show
Sat Dec 08, 2018 12:27 pm by kerabo

» Stadium goggles
Sat Dec 08, 2018 11:37 am by piston 197

» Owners Club Badge
Fri Dec 07, 2018 8:12 pm by PeterW

» Backwards?
Fri Dec 07, 2018 3:22 pm by piston 197


Cruiser 80 Parts

Go down

Cruiser 80 Parts

Post  dodgeyroger on Wed May 30, 2018 5:00 pm

Just got my Cruiser 80 on the road after a two year restoration , been riding around this week and have a "snagging list" . Tool box lid fell off and some inconsiderate motorist ran over it . Throttle sticks and needs new cable. Also would like to fit a rear rack if anyone could help with these parts that would be great, The bike starts 2nd or 3rd kiick from cold, it runs fine but is a bugger to start when hot. only way is to bump start down hill, Any ideas ?

Roger

dodgeyroger

Posts : 16
Join date : 2014-08-31
Age : 63
Location : Long Clawson, Nr Melton Mowbray

Back to top Go down

Cruiser 80

Post  kerabo on Wed May 30, 2018 5:14 pm

How did the toolbox lid manage to fall off?
If it don't start hot is it rich or flooding? Stop it with the petrol off and then only turn on if it starts to see. Is it a paper air filter element as they can get sodden in oil and make rich.
Ken
avatar
kerabo

Posts : 2518
Join date : 2008-02-11
Age : 68
Location : Falcon 87..1936 Cruiser 39. Falcon 81 Green Lane bitsa. Sunbeam S8. Honda Deuville.

Back to top Go down

Cruiser 80 Parts

Post  dodgeyroger on Wed May 30, 2018 5:22 pm

Hi Ken, Lid fell off cos I think I had the fixing screw turned in the wrong direction and it did not click into place . will try your suggestion next time out . Have to do all my trial and error stuff at the top of a hill nearby ha ha . Roger

dodgeyroger

Posts : 16
Join date : 2014-08-31
Age : 63
Location : Long Clawson, Nr Melton Mowbray

Back to top Go down

Lid

Post  kerabo on Wed May 30, 2018 5:27 pm

dodgeyroger wrote:Hi Ken, Lid fell off cos I think I had the fixing screw turned in the wrong direction and it did not click into place . will try your suggestion next time out . Have to do all my trial and error stuff at the top of a hill nearby ha ha . Roger
Have stud or studs on eBay at moment but stainless and not cheap.
avatar
kerabo

Posts : 2518
Join date : 2008-02-11
Age : 68
Location : Falcon 87..1936 Cruiser 39. Falcon 81 Green Lane bitsa. Sunbeam S8. Honda Deuville.

Back to top Go down

Re: Cruiser 80 Parts

Post  dodgeyroger on Wed May 30, 2018 5:45 pm

But I need the whole lid Ken, the screw bit in the centre is about all left salvageable that's how I realized that I had left it in the unlatched position. Roger

dodgeyroger

Posts : 16
Join date : 2014-08-31
Age : 63
Location : Long Clawson, Nr Melton Mowbray

Back to top Go down

Lid

Post  kerabo on Wed May 30, 2018 5:55 pm

Oh if it has a screw it sounds different to what I was thinking of
Sorry.
Ken
avatar
kerabo

Posts : 2518
Join date : 2008-02-11
Age : 68
Location : Falcon 87..1936 Cruiser 39. Falcon 81 Green Lane bitsa. Sunbeam S8. Honda Deuville.

Back to top Go down

toolbox lid

Post  piston 197 on Thu May 31, 2018 10:30 am

Roger , i have sent you a p.m. i have several lids
JH
avatar
piston 197
Moderator

Posts : 4156
Join date : 2008-08-17
Location : ross-on-wye

Back to top Go down

Re: Cruiser 80 Parts

Post  Sponsored content


Sponsored content


Back to top Go down

Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum