Latest topics
» 2t Villiers Electronic Ignition etc
Yesterday at 9:10 pm by stuart elkes

» Cruiser 39 Dynamo
Yesterday at 6:29 pm by piston 197

» Cruiser piston rings needed please
Tue Oct 16, 2018 10:40 am by kerabo

» WIRING HARNESS WANTED
Tue Oct 16, 2018 10:38 am by kerabo

» Stafford Show
Mon Oct 15, 2018 6:39 pm by stuart elkes

» What's this?
Sun Oct 14, 2018 8:34 pm by piston 197

» head bolts 8e
Sun Oct 14, 2018 12:55 pm by alan67

» Copdock and Scotland
Sat Oct 13, 2018 7:21 am by alan67

» 2 7/8" tank badges
Fri Oct 12, 2018 10:00 pm by FrankG


Villiers Decompression Lifter/Lever/Valve

Go down

Villiers Decompression Lifter/Lever/Valve

Post  blackjak on Fri May 11, 2018 7:40 am

Can someone please tell me the what the size and thread is for the bolt that screws into the decompressor to secure the cable to the decompressor? I believe there is a plate between the bolt and the compressor to assist in securing the cable. A 5mm metric bolt will screw in a couple of turns but no more and I do not want to force it. any help appreciated.

Cheers
blackjak

blackjak

Posts : 37
Join date : 2013-10-08
Location : Perth Western Australia

Back to top Go down

Bolt

Post  kerabo on Fri May 11, 2018 8:03 pm

If a 5mm nearly goes in it is most likely 2BA.

If you and a sae I will sad you one but the stamp will cost more than the bolt.

Ken
avatar
kerabo

Posts : 2439
Join date : 2008-02-11
Age : 68
Location : Falcon 87..1936 Cruiser 39. Falcon 81 Green Lane bitsa. Sunbeam S8. Honda Deuville.

Back to top Go down

Bolt

Post  kerabo on Fri May 11, 2018 8:05 pm

Oh I see your Down Under.
Not practice then
Ken
avatar
kerabo

Posts : 2439
Join date : 2008-02-11
Age : 68
Location : Falcon 87..1936 Cruiser 39. Falcon 81 Green Lane bitsa. Sunbeam S8. Honda Deuville.

Back to top Go down

Re: Villiers Decompression Lifter/Lever/Valve

Post  FB vincent on Fri May 11, 2018 9:07 pm

Villiers engine threads are bsf, except for magneto threads which may be ba. Studs screwed into aluminium castings may be bsw. You do not specify the engine type that you are referring to, the thread will definitely not be metric.

FB vincent

Posts : 663
Join date : 2009-01-20
Location : Hertfordshire

Back to top Go down

Re: Villiers Decompression Lifter/Lever/Valve

Post  blackjak on Sat May 12, 2018 12:10 am

Thanks for the info Ken. Yes living in the land down under and still basking in sunshine. 31 degrees today even though it is our autumn. I still have family in the UK and get a lot of parts for the bike and my classic minis sent to them and then have them forwarded on to me. So your offer of an sae was not misplaced. i have ordered some from ebay here in Australia which I am hoping do the job. They say they are from a Triumph, not sure if it is a car or bike, but they are 3/8" long so I don't think I will need to trim them.

cheers
blackjak

blackjak

Posts : 37
Join date : 2013-10-08
Location : Perth Western Australia

Back to top Go down

Re: Villiers Decompression Lifter/Lever/Valve

Post  blackjak on Sat May 19, 2018 8:50 am

Just to say I received my 2BA screws today and it screwed in to the decompressor valve perfectly. Thanks Ken for your suggestion.

blackjak


blackjak

Posts : 37
Join date : 2013-10-08
Location : Perth Western Australia

Back to top Go down

Re: Villiers Decompression Lifter/Lever/Valve

Post  Sponsored content


Sponsored content


Back to top Go down

Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum