Latest topics
» Petrol tanks and spares
Yesterday at 6:37 pm by piston 197

» Cruiser 80 speedo
Yesterday at 5:15 pm by piston 197

» Items wanted
Yesterday at 5:14 pm by piston 197

» Wheel bearings anyone?
Yesterday at 4:55 pm by piston 197

» 1936 Cruiser wiring
Yesterday at 12:34 pm by kerabo

» 1925 350cc fanny b
Tue Dec 11, 2018 6:14 pm by keith.hodgenia

» Spalding Show
Mon Dec 10, 2018 10:24 pm by kerabo

» Owners Club Badge
Mon Dec 10, 2018 9:52 pm by zorteus

» Local meetings
Mon Dec 10, 2018 5:54 pm by nick17


wheel bearing service/ replacement falcon model 58 1953

Go down

wheel bearing service/ replacement falcon model 58 1953

Post  Dadzee on Sat Apr 28, 2018 3:52 pm

Hi Gents
Whilst my rear wheel bearing has no play, it is slightly "notchy" when turning. I expect a thorough clean and repacking with grease would suffice but this seems quite a task with the seal positioning and the bearing location inside the hub.

Has anyone attempted to service them ? or are the bearings and seals readily avaliable and I shouldnt faff about and just fit new ones (If yes, is this an easy job).

Thanks in advance for your advice on this

Cheers Ed

Dadzee

Posts : 18
Join date : 2018-03-25

Back to top Go down

Rear wheel bearing

Post  piston 197 on Sat Apr 28, 2018 5:26 pm

If you have the cup and cone ( bicycle type) bearings sourcing replacements will not be easy, if it is the late type SeriesII with roller bearings not a problem
JH
avatar
piston 197
Moderator

Posts : 4164
Join date : 2008-08-17
Location : ross-on-wye

Back to top Go down

wheel bearings

Post  alan67 on Sat Apr 28, 2018 7:06 pm

Hi Ed as John said if you have the roller type no prob cheep as chips tap old ones out new ones in, done job , but if you have cup and cone and they feel as you say notchy , strip them clean and regreese them,but dont over tighten them they will run for years Alan
avatar
alan67

Posts : 93
Join date : 2017-10-30
Age : 62
Location : lowestoft suffolk

Back to top Go down

Re: wheel bearing service/ replacement falcon model 58 1953

Post  Dadzee on Sun Apr 29, 2018 8:50 am

Hi fellas thanks for your advice. I seem to have standard bearings on the rear but cup and cone on the front so will make sure bthey are not overtightened.
I see that the roller bearings are simple to source but what about the little felt dust washer... is this also readily avaliable ?

Cheers Ed

Dadzee

Posts : 18
Join date : 2018-03-25

Back to top Go down

Rear bearing

Post  piston 197 on Sun Apr 29, 2018 9:04 am

Use bearings with the designation 2RS after the number, these are pre-packed with grease and have rubber seals to prevent loss, you will not need the felt seals then, or can refit your old ones if you wish, but they will be doing nowt !
JH
avatar
piston 197
Moderator

Posts : 4164
Join date : 2008-08-17
Location : ross-on-wye

Back to top Go down

Re: wheel bearing service/ replacement falcon model 58 1953

Post  Dadzee on Sun Apr 29, 2018 10:25 am

Very helpful. Cheers John

Dadzee

Posts : 18
Join date : 2018-03-25

Back to top Go down

Re: wheel bearing service/ replacement falcon model 58 1953

Post  Sponsored content


Sponsored content


Back to top Go down

Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum