Latest topics
» Carburettor needle
Yesterday at 9:06 pm by kerabo

» 8e 197 g/box & clutch help
Yesterday at 9:19 am by Mark9

» New Member
Sat Mar 23, 2019 7:02 pm by stevenbell

» Frame end plugs
Thu Mar 21, 2019 9:07 pm by kerabo

» Falcon Trials & Scrambler Fuel Tanks
Thu Mar 21, 2019 7:58 pm by peter@dunfordconstruction

» New Rims for plover
Thu Mar 21, 2019 7:45 pm by Rex Stewart

» 2019 Event List update
Thu Mar 21, 2019 7:38 pm by John Wakefield

» Cambridge Classic Bike Show
Thu Mar 21, 2019 4:55 pm by John Wakefield

» Old pre-mix.
Mon Mar 18, 2019 4:11 pm by kerabo


Headstock/down tube assembly

Go down

Headstock/down tube assembly

Post  Mikexyz on Fri Nov 11, 2016 3:12 pm

Afternoon,
Wondering if any member has a spare Headstock assembly for either a Cruiser 80/84 or 89 for sale, I believe they are all similar?
The bottom bearing cup holder on mine has been 'got at' by a previous owner + is now no longer round or parallel to the top one.
Any help would be much appreciated.
Regards, Mike

Mikexyz

Posts : 84
Join date : 2010-11-28

Back to top Go down

Down tube

Post  sbeagle on Wed Dec 28, 2016 8:52 pm

I may be able to help out. I have a powder coated one for a Cruiser 80. I also have many parts for a cruiser 84 if needed.

Simon

sbeagle

Posts : 16
Join date : 2016-12-28

Back to top Go down

front frame section

Post  piston 197 on Thu Dec 29, 2016 7:42 am

I have one as well ( 1957 cruiser 80)


JH
piston 197
piston 197
Moderator

Posts : 4317
Join date : 2008-08-17
Location : ross-on-wye

Back to top Go down

Re Cruiser 80

Post  Mikexyz on Fri Dec 30, 2016 12:43 pm

Afternoon.
Thanks for offer but I've managed to repair the 80 frame casting .

If anyone has a spare 89 frame, (the two side/rear parts which bolt onto the front casting) I'd be interested in buying them?

Regards, Mike

Mikexyz

Posts : 84
Join date : 2010-11-28

Back to top Go down

rear frame section

Post  piston 197 on Fri Dec 30, 2016 12:57 pm

I have several sets, but all from the Cruiser 80, they are the same as the 89 , except they do not have the 2 triangular brackets for the cast stand, if you were prepared to fit your own brackets they would do the job ?? I also have a stand for the 89 if required ?
JH
piston 197
piston 197
Moderator

Posts : 4317
Join date : 2008-08-17
Location : ross-on-wye

Back to top Go down

Cruiser 80

Post  peter@dunfordconstruction on Fri Dec 30, 2016 10:07 pm

Hi John,

I would like to buy Mainstand for cruiser 89 if its still for sale?

Regards

Peter
peter@dunfordconstruction
peter@dunfordconstruction

Posts : 355
Join date : 2014-10-28
Location : Lymington Hampshire

http://peter@dunfordconstruction.co.uk

Back to top Go down

centre stand

Post  piston 197 on Sat Dec 31, 2016 7:04 am

Yes Peter, I will send you an Email and picture later today
JH
piston 197
piston 197
Moderator

Posts : 4317
Join date : 2008-08-17
Location : ross-on-wye

Back to top Go down

pictures sent

Post  piston 197 on Sat Dec 31, 2016 11:46 am

Peter. Email with pictures sent
JH
piston 197
piston 197
Moderator

Posts : 4317
Join date : 2008-08-17
Location : ross-on-wye

Back to top Go down

Cruiser 89 frame rails

Post  piston 197 on Tue Jan 03, 2017 12:58 pm

Mikexyz, have sent you a p.m. . I now have a set of frame rails for a 89, and a front downtube section if any one needs one
JH
piston 197
piston 197
Moderator

Posts : 4317
Join date : 2008-08-17
Location : ross-on-wye

Back to top Go down

Re: Headstock/down tube assembly

Post  Sponsored content


Sponsored content


Back to top Go down

Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum