Latest topics
» Speedo drive - Rear wheel
Today at 7:31 pm by peter@dunfordconstruction

» Battery Help
Today at 2:07 pm by FBKev

» Yorkshire police Falcon
Yesterday at 1:02 pm by piston 197

» Cruiser oil
Mon Jan 21, 2019 6:48 pm by kerabo

» One from every year
Mon Jan 21, 2019 8:12 am by piston 197

» American thoughts of a British Bike Cruiser 39.
Sun Jan 20, 2019 5:10 pm by John Wakefield

» NEW CLUB MEMBERS
Sun Jan 20, 2019 10:40 am by piston 197

» Cruiser 39 gear change
Sat Jan 19, 2019 5:16 pm by kerabo

» Re-register Cruiser/Falcon
Sat Jan 19, 2019 1:08 pm by peter@dunfordconstruction


Gearbox strip down

Go down

Gearbox strip down

Post  Andrewwoey on Thu Sep 22, 2016 4:58 pm

Over winter i will open up my gearbox to try and cure the leak from the kick/gear shaft (4 speed on 8e).

Is there anything i need to watch out for when dismantling it? Any springs or other items that's going to shoot out?

Andy.

Andrewwoey

Posts : 83
Join date : 2016-08-08
Location : Wolverley, Worcestershire.

Back to top Go down

Re: Gearbox strip down

Post  Jack Clegg on Fri Sep 23, 2016 9:13 am

No spring surprises. Make sure the mainshaft stays put when removing inner case. You may be able to leave the clutch intact on the other end.
Jack Clegg
Jack Clegg

Posts : 367
Join date : 2012-11-12
Age : 55
Location : Marlow

http://jackclegg.com

Back to top Go down

Re: Gearbox strip down

Post  Andrewwoey on Fri Sep 23, 2016 8:32 pm

Jack Clegg wrote:No spring surprises. Make sure the mainshaft stays put when removing inner case. You may be able to leave the clutch intact on the other end.

That's great. Thanks for the information. Hopefully no drama's when i do the job.

Andy.

Andrewwoey

Posts : 83
Join date : 2016-08-08
Location : Wolverley, Worcestershire.

Back to top Go down

Re: Gearbox strip down

Post  banjo boy on Fri Sep 23, 2016 9:20 pm

Hi Andy
I have built a few gearboxes over the years,my first one which was a Burman 52 I was a bit worried about stripping it down but once I started to strip it down I realised how fairly simple they are and enjoyed re building it. Just take your time and take a picture for ref at every stage before you take apart this helped me just in case ,and last of all a exploded view of the gear box so to check things are in correct order.

Regards
Laurence
banjo boy
banjo boy

Posts : 249
Join date : 2013-10-22
Age : 54
Location : cambridgeshire

Back to top Go down

Re: Gearbox strip down

Post  Andrewwoey on Fri Sep 23, 2016 9:52 pm

banjo boy wrote:Hi Andy
I have built a few gearboxes over the years,my first one which was a Burman 52 I was a bit worried about stripping it down but once I started to strip it down I realised how fairly simple they are and enjoyed re building it. Just take your time and take a picture for ref at every stage before you take apart this helped me just in case ,and last of all a exploded view of the gear box so to check things are in correct order.

Regards
Laurence

Thanks for the great advice. I am used to Japanese engines but still do the same with the photo's. I look forwards to this winters gearbox repair. Its dripping lots, so it as to be done.

Andy.

Andrewwoey

Posts : 83
Join date : 2016-08-08
Location : Wolverley, Worcestershire.

Back to top Go down

Re: Gearbox strip down

Post  banjo boy on Sat Sep 24, 2016 9:53 am

Andy glad to be of help,If it has a oil leak which most do,make sure the surfaces are flat, I used a nice flat surface and some wet and dry.
If you have built Japanese then you will have no trouble with these gearboxes.

Laurence
banjo boy
banjo boy

Posts : 249
Join date : 2013-10-22
Age : 54
Location : cambridgeshire

Back to top Go down

Re: Gearbox strip down

Post  Andrewwoey on Sat Sep 24, 2016 10:47 am

banjo boy wrote:Andy glad to be of help,If it has a oil leak which most do,make sure the surfaces are flat, I used a nice flat surface and some wet and dry.
If you have built Japanese then you will have no trouble with these gearboxes.

Laurence

The leak is from the gear/kick start shaft. I understand there is a O ring in there.

Andy.

Andrewwoey

Posts : 83
Join date : 2016-08-08
Location : Wolverley, Worcestershire.

Back to top Go down

Re: Gearbox strip down

Post  banjo boy on Sat Sep 24, 2016 12:12 pm

Andy I can't comment on that as my bike has a AMC gearbox, but I would say if the set up is similar then it will have a O ring on the outer casing if it is then you may not have to do a full strip down,not unless you want to check it out and replace bearings etc.Just make sure that the o ring is same size as metric ones are a little smaller,eg 1/4 =6.35 so this can make a difference between sealing and not sealing. But I am sure there is someone here on the forum who knows more on your gear box and what to look out for.

Laurence
banjo boy
banjo boy

Posts : 249
Join date : 2013-10-22
Age : 54
Location : cambridgeshire

Back to top Go down

Re: Gearbox strip down

Post  Andrewwoey on Sat Sep 24, 2016 12:27 pm

Yes learning a lot about imperial and metric sizes. Built many Japanes engines and bikes over the years and now enjoying and learning about old British bikes and engines.
Thanks for the advice.

Andy.

Edit. Just done an inspection and its leaking in many places/joints. I will pul the motor out over winter and give it a once over.

Andy.

Andrewwoey

Posts : 83
Join date : 2016-08-08
Location : Wolverley, Worcestershire.

Back to top Go down

Grease nipple

Post  Andrewwoey on Sun Sep 25, 2016 3:56 pm

Should there be a grease nipple in the end of the kick start shaft? In the parts diagram its number 56 (4 speed).

Andy.


Andrewwoey

Posts : 83
Join date : 2016-08-08
Location : Wolverley, Worcestershire.

Back to top Go down

Re: Gearbox strip down

Post  banjo boy on Sun Sep 25, 2016 5:05 pm

No Andy what you have there is a centre drilled hole to enable the shaft to have been ground when it was made.

regards

Laurence
banjo boy
banjo boy

Posts : 249
Join date : 2013-10-22
Age : 54
Location : cambridgeshire

Back to top Go down

Re: Gearbox strip down

Post  Andrewwoey on Sun Sep 25, 2016 7:20 pm

banjo boy wrote:No Andy what you have there is a centre drilled hole to enable the shaft to have been ground when it was made.

regards

Laurence

Thank you again Laurence.

Andy.

Andrewwoey

Posts : 83
Join date : 2016-08-08
Location : Wolverley, Worcestershire.

Back to top Go down

Re: Gearbox strip down

Post  Sponsored content


Sponsored content


Back to top Go down

Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum